Products
1 Records   1
                       

Quartz Sleeve

 

We provide quartz sleeve for the uv lamp.
Standard clear quartz glass tube is high quality purity and automatic controlled fusing furnace
It has the characteristics of high purity,strong resistance,high transmission and accurate dimensions,and the OH content 1-20ppm after air of vacuum baking is available.

 

REPLACEMENT OF THE QUARTZ SLEEVE

1. Unplug system, turn pump off Remove Lamp and Transformer.Drain the Housing

 

Quartz Sleeve


Note: If you have the Wiper option, fully extend the wiper rod outward.

2. Untwist EZ Twist Top. This will release the Quartz Sleeve Assembly. Pull The Quartz Sleeve Assembly straight out of the housing.

Quartz Sleeve



3. Untwist Quartz Cap. Push Quartz Sleeve up through EZ Twist Top. Be careful not
to break the Quartz Sleeve. Handling broken glass can cause injury. If your

 Quartz Sleeve is broken protect your hands before servicing.

Quartz Sleeve


 

4. Discard old Quartz Sleeve and Rubber Seal.

5. Be sure the EZ Twist Top has the O-ring inside then re-install EZ Twist Top without Quartz Sleeve. The Rubber Seal should be about 1/4” down from the open ended side of the Quartz Sleeve. Insert the Quartz Sleeve through the EZ Twist Top straight into the housing. Be sure the Quartz Sleeve is seated in the cup inside the bottom of the unit.

 

Quartz Sleeve

 

Note if you have a the Wiper Option:
Wet the Wiper Blades and the outside of the Quartz Sleeve with water, do not use any lubricant. Push the rod completely into the unit and insert Quartz Sleeve through the blade(s). Please note units that use 40 Watt Lamps have 2 Wiper Blades, be sure to insert Quartz Sleeve into both Blades. Be sure the Quartz Sleeve is seated in the bottom of the UV Body.

Quartz Sleeve


6. Gently push the Quartz Sleeve and Rubber Seal in to the EZ Twist Top
until only 1/2 the rubber seal is visible. Twist on the Quartz Cap. Do Not Use
any tools tighten by hand.

Quartz Sleeve



7. Turn the pump on, start water flow through the system and check for leaks. If the unit leaks in one or more of the following areas, see installation manual on the web at aquaultraviolet.com. If there are no
leaks continue to step number 8.

 

Quartz Sleeve


8. Unscrew the Davis Connector located behind the Transformer
Cap, this allows your Transformer Cap to spin freely.

 

Quartz Sleeve


9. Plug the Lamp flush into the Lamp End Connector before inserting the Lamp into the unit. If the Lamp is not plugged in all the way it may cause damage to the unit and is not covered under warranty.

10. Insert the Lamp straight into the Quartz Sleeve. Be careful, inserting the Lamp at an angle,even a slight angle, can cause a "U" shaped crack in the Quartz Sleeve.

11. Twist the Transformer Cap onto the Quartz Cap. Do not over tighten.
This is a connection only and is not in contact with water.

Quartz Sleeve



12. Tighten the Davis Connector back on to the Transformer Cap.

13. Check for Leaks See Number 7.

14. If there are no leaks, plug unit in to a GFCI outlet.

LED Bulb, LED Tube, UV Lamp, COB LED Light, Rechargeable LED Flashlight, LED Camping Lanterns
China UV Lamp & Amalgam Lamp manufacturer,Wholesale Hot Cathode Quartz UV Lamp, Cold Cathode Quartz UV, Reptile Lamp, Amalgam Lamp with high quality and low price.
Copyright ©Ningbo Sunfine UV lighting Co.,ltd.
Internet Marketing By Netcec Link